Reviews

Based on 1285 reviews
89%
(1146)
9%
(115)
1%
(12)
1%
(7)
0%
(5)
EBB 36 CAN V1.2(G0B1)

+Good manual & documentation! This is very important to me!
+Came with a bag of connectors and crimp pins/sockets needed for wiring! Huge time & cost saving.
+Cleans up wiring a lot, I had 17 wires in my umbillical before, now i have 4.
+MAX31865 improved the accuarcy of my PT-1000
+Small with good fit and finish
+Low weight
- ADXL245 pins INT 1 or INT 2 not connected to MCU. Makes it impossible (for now) to use the ADXL245 as Z-probe.
In total 5/5, because i already have a bed probe :)

Great way to modify an order

Much easier than canceling and reordering

Amazing quality

With all the orders I did so far at BTT, this is also perfect. Packaging is good, product itself is just as discribed and works flawless!!

A better printer probe

This is the third of the Micro Probes that I have installed on my 3D printers and it is the V2.0 best of the best. It's footprint, accuracy, and ease of use in my view out performs the BL Touch and the CR Touch. It would be great if a little more information for the printer.cfg file were in the box. You can't go wrong with this probe and the price is perfect.
Doc'

Awesome board at a nice price range

So my board arrived a week ago and after printing for a while, I must say I am impressed by the board. It's super quiet, no whining from stepper motors and quite reliable. Installation was easy, aside from hot end fan (you have to make a jst connection from 2 wires), but that is creality's fault, not the board manufacturer. Also gives a ton of upgrade space that is mostly plug and play (lcd, probe...) All in all, I am super pleased with the purchase

Nice one

Nice one, quiet drivers it’s insane! But still need to ground the step motors

The Board works really well, I am very satisfied

LDO-36STH20-1004AHG(XH) Motor for Voron 0.1 & Voron Stealthburner

Good Product

But no duck in the box :(

Silent Ender 3

Top quality product, making the Ender 3 silent.

Excellent board

Excellent board. Although I fried it while diagnosing a bed heating issue (I ran a very large bed on the Bed-out, rated at 24V, 10A). I've ordered a new one. Only thing I can complain about is the long shipping time to Europe.

High Quality and fast delivery

Same as in title- love the little duck

Fast shipment, great product

Fast shipment, good price, great product!

U2c works

Connected for my V0 check the cables connectors on the u2c and the ebb and verify you can fry your ebb easy, if its installed correctly works wonderful for the skr pico

Solid upgrade - a big step up in performance

This was my first hot end replacement after upgrading almost everything else but the printer's frame. I am very glad I chose the H2 V2S.

While waiting for delivery I was able to adapt and print the parts I needed to attach it to my Voxel Aquila X2. In the end I replaced the Aquila X-carriage for a stock Ender 3 carriage as that gave me access to more proven starting designs for the mounting plate.

All the bundled electrical parts seem to be of quality, the the heater cartridge leads were already crimped which was nice to see. The H2 V2S mechanical design is beautiful and so compact, I was amazed at how small it was once it was in my hand. The manual gear operation is smooth it shouts quality. The filament release has a satisfying click. In operation it is silent with the occasional quiet click of retraction (when retraction is set to at 0.5mm @ 5mm/s - my bowden setting of 45mm/s makes it a bit chatty :) ).

I really like the consistent 3mm mounting holes all over the H2 V2S and its symmetric geometric design, it makes designing accessories easy. I've secured it to the backplate from the top and back to help minimise flexing of the PETG backplate. By the way, the dimensioned drawing has some missing y-plane dimensions for the nozzle - I want to redesign my cooling duct and this would really help.

I was initially concerned about the 35mm fan not cooling enough and making too much noise but I was very wrong. Even in my longest print so far (4hrs @ 240deg PETG) there has been no sign of over-heating and it really is virtually silent - well done BIQU! (I say that as someone who replaced all the stock fans on their printer so I can share the room with it). I've initially chosen a 5015 blower with a three pronged duct as a part cooler and that is the noisiest part of my printer now but it is still very acceptable and it gives good results up to 70-degree overhangs. Most of the noise comes from the blower's narrow ducts so I'll experiment with other designs.

My printer's cable runs are a bit longer than a stock Ender, another 20cm on all cables would have been great but the installation was straight forward. I rerouted cables to get enough length for the head to reach full z-height and still get to the far right x-axis. Initially frustrating but not a big deal in the end. I would have liked the stepper motor lead to be terminated with a locking connector (HS?).

With the BIQU H2 V2S I've only just begun pushing speed but already I've achieved 100mm/s on everything. There is more speed to be had, 200mm/s gives very acceptable results but I think I need to upgrade my part cooling. The 100mm/s benchy was my best ever, the 200mm benchy was way better than my printers's original 60mm/s. I've printed about a dozen things so far (in PLA and mostly PETG) not a single issue with the H2 VS2 and all came out with better quality than I am used to.

Great product

I’ve purchased this screen for my Voron Trident 300 easy install of Klipperscreen with no other drivers required. I like the V1.2 they moved the HDMI and USB-C port back from the edge makes for a cleaner installation of those two cables.

BIGTREETECH Panda Touch V1.0 - 5 Inch Touch Screen with Multi-Printer, Wireless Control For Bambu Lab X1, P1 and A1 Printers - Check firmware compatibility before purchase

Great addition.

WOW this is a nice and easy to setup and to use. i would like to see after your print is finished that the main screen would stay the same as it is with the finish icon on it, not togo the gray screen. Please a the camera to it so we can see whats going on if it is taking to a different area .

P
CNC Voron Tap V2/V1
Petre Florin

CNC Voron Tap V2/V1

One of the best boards

I have put this board on delta printer, it behaved as expected and exceeded expectatipns on how easy it was to program it. One flaw that i have foud is the lack of one dedicated connection for BTT SFS V2, I have used LED port to program in switch sensor, but regardin this the board is flawless.

BIGTREETECH EBB 36/42 Can Bus U2C V2.1 for Connecting Klipper Expansion Device Support PT1000

works fine with klipper

Works well, the only gripe I have is I had to hack together an adapter board so I could keep using the reprapdiscount-style 2004 display

What are you looking for?

Your cart